Find Best Recommendation Curing Light, Pen-type Best Curing Light, Best Curing Light Of All on Industry Directory, Reliable Manufacturer/Supplier/Factory from China.

Inquiry Basket (0)
Home > Products > Light pen > LED Dual Wavelength Curing Light Pen

LED Dual Wavelength Curing Light Pen

LED Dual Wavelength Curing Light Pen

    Packaging: By paper box
    Productivity: 100 units / month
    Brand: ELiTEDENT
    Transportation: Ocean,Air,Express
    Place of Origin: Taiwan
    Supply Ability: 100 units/month
    HS Code: 9018
    Port: Port of Keelung

Basic Info

Model No.: Q6-NLG

Product Description

Battery Charging

To charge the battery, place the handpiece in the charging base, with the power supply attached to the charging base. When this is done, the POWER INDICATOR will illuminate.

The Curing Light may be used with the power supply attached to the handpiece handle, even if the battery is low. While in this configuration, the battery will charge while the unit is not being used. When the handle is removed from the charger, or the power disconnected, none of the battery indicators will illuminate.


Package includes:

Charging Base Assembly

Hand piece Assembly

Eye shield

Wall Plug-in Power Adaptor

Instructions For Use


The ELiTEDENT Q6-NLG is a Pen-type Curing Light, cordless, high-performance LED light source curing unit intended for polymerization of resin-based light cured dental materials by dental professionals. ELiTEDENT Q6-NLG incorporates two types of LEDs to achieve broad wavelength with the range of 390 to 480 nm output to polymerize virtually all the resins in the market and a high power mode to produce super fast curing effect. The relevant range both for camphorquinine (CPQ) and phenyl propanedione (PPD) containing product. Though the majority of light-curing dental materials are responsive in this range of wavelengths, it is suggested you should contact the filling material maker to make sure it before use.

The ELiTEDENT Q6-NLG is a fast-curing LED Curing Light. It emits typical light energy output at about 2,000 - 2,200 mW/cm². 3 seconds to cure most composite in the market with 2mm thickness. It also features:

Multiple mode selection: High (fast curing), low and ramp up.

All aluminum handpiece housing for improved durability. No more plastic to stain or crack.

Two button easy operation.

Quiet operation, fan-free design.

Can be used both cordless and corded.

Low battery warning; for urgent use, just insert power cord connector into Handpiece directly.

Rechargeable lithium battery inside, capable of 200 x 10 sec curing cycles prior to recharging.

Slim handpiece for most comfortable hand holding

► Curing tip rotates 270∘for curing at any position of mouth.


Initial set-up

NOTE: Upon receiving the LED Curing Light, check the packaging and parts for any possible damage

that may have occurred in transit. If damage is apparent, please contact your authorized Rolence distributor from which the light was purchased.

1. Remove the contents from the shipping package. Be careful not to drop or impact the Curing Light. Choose a flat, level, sturdy surface to place the charging base on. The light is shipped in a “sleep” mode, and no timer display. To wake the unit, press the On/Off button.

2. Before using for the first time, the Curing Light must be fully charged. For the first charge, this process will take about 6 hours. Use only the power supply furnished with the light system. Attempting to use another power supply source may cause injury or damage and will void the warranty.

3. Charging indicator on charging base illuminates orange light during recharging. It will turn off automatically after battery is fully charged.

NOTE: Power indicator on charge base illuminates blue light, which indicates the charging base is well connected to power supply. If power indicator is not lit when connecting power plug to charging base, please check the outlet plug is firmly connected or not.

4. Plug the connector of the power supply into the back of the charging base. Plug the other end of the power supply into the appropriate electrical outlet. As mentioned above, wait for at least 6 hours to completely charge the light before the first use.

NOTE: Verify the line plug of the power supply plug is properly rated for your facility, and that all connections comply with safe practices and all local requirements. Always use unit in conjunction with a properly grounded outlet.

Keypad and modes

There are 2 buttons on the keypad for the mode/timer selection, and the on/off button. The on/off button is used to activate and deactivate the light. Push once to turn on the light and push it again if you need to turn it off at any time during the curing cycle.

There are 3 different modes to select from based on the procedure and the requirement.

- Select the exposure time by pressing the mode button briefly.

- While exposure is ongoing, the button for selection of the exposure time is inactive.

(3s or H) – This setting provides high power to the LEDs, helping them generate a higher power output up to 2,000mW/cm². Since the LEDs function at such high power level, only the 3 second curing cycle is provided to avoid premature LED failure. You can use multiple boost cycles in succession to obtain longer Boost curing.

(10s or L) – Provides low light energy exposure at 10 seconds exposure. Choose this setting for special lighter or darker shade curing requirement or when light energy declines after long time use.

(Ramp Up) - An initial 45 - 60% energy of high intensity and then switch to high intensity 2,000 mW/cm² constant. Total 5 seconds (3 seconds low intensity + 2 seconds high intensity).

Rolence Enterprise Inc.

  • 1
  • 2
  • 3
  • 4
 

Rolence Enterprise Inc. headquartered in Taiwan, develops, manufacturing & innovation on small equipment of Ultrasonic Scaler, Portable X-Ray, Dental Digital Sensor and LED Curing Light...etc. For over 40 years, we are an international supplier of dental equipment for various companies .


Multi-innovative developments & processes, proven know-how and high-quality have given us a leading position to our customer. and keep up with the innovative and creative design concepts into our products chain by incorporating the dentists` and other technology industry needs.


Besides, with further office locations will be in Germany, we will keep expending our office establish in different country afterward, and supporting our customer latest information, product training, and marking media to increase your business, that`s why we are approaching you to present ourselves & the products to reach a good cooperation in the future.

Company Info

  • Company Name: Rolence Enterprise Inc.
  • Representative: Sterling Cheng
  • Product/Service: Portable X-Ray , Curing Light , Ultrasonic Scaler , Curing Box , Dental Digital Sensor , UV Spot Curing
  • Capital (Million US $): TWD$65,400,000
  • Year Established: 1981
  • Total Annual Sales Volume (Million US $): US$2.5 Million - US$5 Million
  • Export Percentage: 81% - 90%
  • Total Annual Purchase Volume (Million US $): US$1 Million - US$2.5 Million
  • No. of Production Lines: 3
  • No. of R&D Staff: 5 -10 People
  • No. of QC Staff: Fewer than 5 People
  • OEM Services Provided: yes
  • Factory Size (Sq.meters): Below 1,000 square meters
  • Factory Location: No. 18-3 , Lane 231, Pu Chung Rd., Chungli Dist., Taoyuan City, Taiwan R.O.C. 32083
  • Contact Person: Mr. Peter Chiu
  • Tel: +886-3-4631999
Email to this supplier
  • *Subject:
  • To:

  • *Messages:
    Your message must be between 20-8000 characters